How To Clean Tile Floors To Remove Soapy Water

Download Article

Download Article

No matter how ofttimes you clean your bath, soap scum is going to build upwardly on the tile in your shower and/or bathtub from time to time. Unfortunately, you lot commonly tin can't scrub it off with conventional soap and water. Instead, you must employ specific cleansers that cutting through the thick scum so it volition loosen enough to scrub off. Commercial tile and bathroom cleaners work well for removing soap scum, but yous can also make your own with dish detergent and vinegar. If y'all prefer all-natural cleaning products, a paste made from baking soda and vinegar tin as well practise the trick. The central to using whatever of the cleansers to remove soap scum is patience, though -- you must leave them on the tile for at least a few minutes so they take time to break downwards the soap scum.

1. i

   Spray the tile with a targeted tile cleaner. A commercial bath or tile cleaner is ofttimes the easiest way to get rid of lather scum because it is formulated specifically to go rid of the stubborn residue. Utilize a generous coat of the cleaner to the dingy tile according to the bottle's instructions.^[1]

   • Tile or bathroom cleanser typically comes in two formulas: a liquid or foam spray. A liquid spray is effective on horizontal tile surfaces where you lot don't take to worry almost it dripping.The foam is often easier to employ on tile walls because information technology stays in place without dripping off.
   • Ever read the instructions on a commercial tile or bathroom cleaner earlier using it on any tile.
   • Earlier applying the cleaner all over the tile, test information technology in a small, inconspicuous expanse to ensure that it won't impairment the tile.

2. two

   Allow the cleaner to sit on the tile for several minutes. Once you utilise the tile cleaner to your tiled surfaces, yous must allow it to sit down for approximately 3 to 5 minutes. That gives the cleaner time to cut through the soap scum and residue so you lot tin easily remove it.^[2]

   • Some cleaners may need to be left on longer than 5 minutes. Consult the bottle's instructions to decide the proper amount of time.

   Advertisement

3. three

   Wet a sponge and wipe downwards the tile. Afterwards the cleaner has sat on the tile for several minutes, run a sponge under warm water. Apply information technology to carefully wipe downward the tile and remove the soap scum and cleaner residual.^[3]

   • Make certain to employ a non-abrasive sponge or you may scratch the tile. You tin substitute a damp cloth for the sponge if you adopt.
   • If there are areas of the tile where the soap scum is especially stubborn, you lot may need to use a soft scrub brush to remove the residuum. Be careful not to scrub too hard, though, or you may scratch the tile.

4. 4

   Rinse the tile with warm water. When you've wiped abroad all of the soap scum and cleanser residue with the sponge, fill a spray bottle with warm water. Spray the tile with the water to rinse the surface until it's clean.^[4]

   • If you lot don't have a spray bottle, you can wet a cloth with warm h2o and utilise it to rinse the tile.

5. 5

   Dry out the tile. To go on the tile from developing more soap scum or mildew, it's important to dry it completely. Use a squeegee or towel to thoroughly dry out the unabridged surface.^[5]

   Advert

1. 1

   Measure equal parts of vinegar and dish soap. To make homemade soap scum cleaner, you'll need equal parts of white vinegar and dish soap. You can make as little or as much of the cleaner as you'd like, so adjust the amounts accordingly to accept 1 office of each.^[six]

   • If you want to make enough of the cleaner to utilise repeatedly, information technology's best to measure between 1 and 2 cups (237 to 473 ml) of both the vinegar and dish detergent.

2. 2

   Warm the vinegar in the microwave. Once you've measured out the vinegar and dish soap, transfer the vinegar to a microwave-safe bowl. Oestrus it in the microwave for xxx seconds to ane minute or until it is hot only not humid.^[7]

   • Heating the vinegar makes it easier to blend it with the thick dish soap.

3. 3

   Combine the vinegar and soap in a spray bottle and milkshake information technology to mix. After you've heated the vinegar, cascade it into a spray canteen. Add an equal amount of the dish soap, and secure the hat on the bottle. Shake it well to mix the two.^[8]

   • Exam the spray after y'all've mixed information technology. If it'south too thick to spray, yous can mix in a fiddling bit of warm, distilled water to thin it out.

4. 4

   Spray the mixture over the tile and let it sit down. When you're fix to apply the cleaner, spray a generous amount over the afflicted tile. Let the spray to sit on the tile for at to the lowest degree 30 minutes so it has time to cut through the soap scum.^[9]

   • If the tile has a particularly thick layer of lather scum, you lot may want to get out the spray on the surface for an hour or longer.

5. 5

   Wipe the tile down with a damp sponge and rinse information technology clean. After yous've allow the cleaner sit on the tile for a one-half hr or longer, use a damp sponge to wipe the soap scum and remainder away. Next, spray the area with warm water to rinse it completely clean.^[10]

   • If the lather scum isn't wiping away on the sponge, yous tin can use a soft scrub castor to work on the stubborn areas. Scrub lightly, though, to avoid scratching the tile.
   • If you don't have a spray bottle to rinse the tile, wet a make clean cloth or rag with warm water to rinse it.

6. 6

   Dry out the tile. In one case the tile is rinsed clean, use a clean towel or rag to wipe downwards the surface so information technology is completely dry. Go along the canteen of cleanser with the residue of your cleaning supplies, and use anytime that you observe lather scum buildup.^[11]

   • The homemade lather scum cleaner should stay effective for 6 months to i year.

   Advertizement

1. 1

   Mix the baking soda and vinegar. If you lot prefer an all-natural tile cleaner, add together one cup of baking soda (180 g) to a bowl. Drizzle in just enough white vinegar to create a thick paste.^[12]

   • Information technology's normal for the mixture to fizz when you combine the ingredients.

2. 2

   Apply the mixture to the tile and allow information technology sit down. Once the blistering soda and vinegar mixture stops fizzing, apply it the dirty tile with a damp sponge. Let the mixture to sit on the surface for at least xv minutes then it has time to break down the soap scum.^[13]

   • You may want to get out the blistering soda paste on the tile for up to a half hr if the soap scum is particularly thick.

3. 3

   Wipe the mixture off with a sponge and rinse the tile off. After you've immune the baking soda paste to sit down on the tile for at least 15 minutes, wet a clean, not-abrasive sponge and wipe information technology abroad. Next, use a spray canteen filled with warm water to thoroughly rinse the tile then it's completely clean.^[14]

   • If there are some areas where the lather scum hasn't come off, y'all can scrub them with a soft-bristled brush.

4. 4

   Dry the tile. When the tile is completely clean, utilise a clean towel or cloth to wipe down the surface. Information technology's important to dry the tile completely if you want to keep the surface free of soap scum and mildew.^[15]

   Advertisement

Add New Question

• Question

  How practice y'all remove heavy soap scum?

  

  Heather Isenberg is a habitation cleaning expert and the Owner of The Tidy Maiden, a residential and commercial cleaning service company serving the San Jose and Los Angeles, California regions. Heather's business The Tidy Maiden and Heather'south book The Automated Bosslady were recently featured on CBS.

  

  House Cleaning Professional

  Expert Answer

• Question

  Tin can you employ these on drinking glass shower doors?

  

  Both the vinegar and detergent mixture and the vinegar and baking soda mixture are safe to use on soap scum on drinking glass shower doors. If you're using a commercial bath cleaner, make sure that the label says information technology is prophylactic to use on glass.

Inquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advert

• Avoid hard water stains and lather scum stains by wiping down your shower with a squeegee or hand towel subsequently each utilize.

• No matter what type of cleanser y'all're using to remove the lather scum, brand sure that your bathroom is properly ventilated before you start cleaning. Open a window and/or turn on a fan so the fumes don't bother you.

Advertisement

Things You'll Need

• Commercial tile or bath cleaner
• Sponge
• Spray bottle with warm h2o
• Duster or towel

• Measuring loving cup
• Microwave-rubber bowl
• Spray bottle
• Sponge
• Towel or rag

• Bowl
• Spoon
• 2 sponges
• Towel or material

About This Article

Article Summary X

To remove soap scum from tile, showtime by mixing equal parts white vinegar and liquid dish soap. You tin can also make a paste using blistering soda and white vinegar. Once yous've made your cleaning mixture, apply information technology to the tile you want to make clean and let it sit for 30 minutes. Later xxx minutes, wipe down the tile with a damp sponge and rinse the tile with clean h2o. To learn how to remove soap scum from tile using commercial products, keep reading!

Did this summary help you?

Thank you to all authors for creating a page that has been read 269,306 times.

Did this article help you?

Source: https://www.wikihow.com/Remove-Soap-Scum-from-Tile#:~:text=To%20remove%20soap%20scum%20from%20tile%2C%20start%20by%20mixing%20equal,it%20sit%20for%2030%20minutes.

Posted by: mcwilliamssamalmot.blogspot.com

Share this post